THE TRAP CAGE.

[Ill.u.s.tration]

Among bird-catchers generally, this is the favorite and most universal trap; and, where a _decoy_ bird is used, it is particularly successful.

The cage is arranged in two compartments, [Page 77]

one above the other,--the lower one being occupied by the call-birds.



The making of the cage requires considerable ingenuity and much patience; and, for the benefit of those who may desire to exercise that patient ingenuity, we will subjoin a few hints, which may help them along in their efforts. For an ordinary cage, the height should be about one foot, the broad sides the same, and the top and other two sides eight inches. First cut four corner uprights.

These should be three-quarters of an inch square, and one foot in length. Next cut a bottom board of pine, twelve inches by eight inches, and one inch in thickness. From each of its corners, cut a small cube of the wood, exactly three-quarters of an inch square, thus leaving four notches, which will exactly receive the ends of the uprights, as seen at (_a_). Before adjusting these pieces, the four sides of the boards should be pierced with small holes, as is also shown in the diagram (_a_). These may be punched with a brad-awl, and should be about half an inch apart, and three-eighths of an inch from the edge of the board. Each one of the uprights may then be secured in place by two long brads, one being hammered each way into each side of the notch. Next proceed to cut four more of the square sticks. Two of these should be one foot in length, and the remaining two eight inches. The corners of these should now be neatly bevelled off, so as to fit after the manner of a picture-frame. They should then be attached to [Page 78]

the upper ends of the uprights by a brad through the corner of each, as seen at (_b_), the dotted lines indicating the end of the upright beneath. These sticks should likewise be pierced with holes to correspond with those in the bottom board, and running up and down in the direction of the wires.

[Ill.u.s.tration]

The middle tier of braces are next required. Two of these should be ten and a half inches in length, and the other two six and a-half, and the ends should be perfectly smooth. These should now be punched with holes corresponding with those above, after which they may be inserted between the uprights as seen in the engraving, and secured by a brad at each end.

The trap door is shown separate at (_c_). The side sticks should be eight inches in length, and one-half an inch square, and the top and bottom sticks five inches in length. They should be set in _between_ the side sticks, and the lower one should be secured about half an inch above the lower ends of the uprights, as seen in the ill.u.s.tration. The holes should be made in the side pieces, and the wire run across from side to side, as shown. Annealed iron, or copper wire is best for this purpose. The door should now be pivoted or hinged at the top of the cage, between the long sides, in such a position as that the top end shall rest on one of the narrow upper edges of the cage. A stiff wire should be used for the hinge, being pa.s.sed through the top pieces of the cage into the lower ends of the door pieces. The cage may now be wired throughout.

This is an easy matter, if the holes are properly made. About thirty yards of the wire will be required: iron wire is generally used.

It should be about the size of a hair-pin, and should work easily.

Commence by pa.s.sing it from the under side of the bottom board through one of the holes next to the corner. Pa.s.s the wire upward, through the centre braces, again upward through the top piece and across to the opposite broad side and corresponding hole. From this point it should pa.s.s downwards, through centre brace, and again through the bottom. Draw the wire tightly and pa.s.sing it upward through the hole next to it, bring it over the top of the cage and around again to the bottom edge from which it started.

Continue thus until the hinge of the door is reached; after which the wire should be pa.s.sed up and down on the same side and thus carried around the small end of the cage until it finally meets at the door hinge on the opposite side. The two halves of the cage should now be separated by a grating of wire, as seen in the main [Page 79]

ill.u.s.tration. This may be accomplished either by pa.s.sing the wire from side to side, around the base of each upright wire, or an additional horizontal row of holes below the others may be punched for the purpose. The door through which the call-bird is introduced should next be made in the bottom section. There are two ways of doing this: one method consists in sawing a hole three inches square in the bottom board of the cage; and a cover consisting of a piece of tin is made to slide beneath the heads of four tacks, two of which are placed on each side of the opening. This form of door is perhaps the simplest of the two. The other is shown separate at (_f_), together with its mode of attachment.

It consists of two side pieces of wood, about a third of an inch square, and three inches in length, and two shorter ones, two inches in length. These are arranged into a square framework by a board in each corner. Four holes are to be pierced in each side piece, at equal distances. Commencing at the top, the door should then be wired as directed for the cage. The lowest hole on each side should be left open for a separate piece of wire. The cage should now receive attention. The broad side is generally selected for the door. Find the seven centre wires and connect them across the middle by another horizontal bit of wire. This may be easily done with a pair of pincers, by compressing a loop at each end of the wire around the two which run perpendicularly at its ends. When this is performed the five intermediate wires should be cut off about a quarter of an inch below the horizontal wire, and the projecting tips looped back over the cross piece, and made fast by the pincers.

The lower parts of the upright wires may now be cut off close to the board. We will now take up the door. Pa.s.s a piece of wire through the holes at the bottom, clap the door over the opening, and loop the ends of the projecting wire loosely around the upright wires at each side. This will allow the door to slide easily up and down.

Another wire should now be interlaced downwards through the centre of the door, and bent into a ring at the top. Let the door rest on the bottom of the cage, and, while in this position, adjust the ring at the top around the central wire directly behind it.

The door is then complete, and, if properly made, will look neat and work easily.

The "trap" at the top of the cage is next in order. To complete this it is first necessary to interweave a _stiff_ wire loop, as seen at (_d_). The loop should extend on the _inside_ of the lower piece of the door and about two inches below it. The [Page 80]

_spring_ power consists of a piece of stiff hoop-skirt wire, interwoven between the wires of the top of the cage, and those of the door, while the latter is shut. The force of this will be sufficient to bring down the door with a snap; and for further security a catch, such as is described in page (88), may be added if desired.

The spindle is next required. This is shown at (_g_), and consists of a small perch of wood seven inches in length, and notched at each end. In setting the trap, the door should be raised as seen in the main ill.u.s.tration. One of the notches in the spindle should now be caught beneath the loop and the other around one of the central wires in the end of the cage. The bait, consisting of a berry, bird-seed, or what-not, may be either fastened to the spindle or placed beneath on the wires. The call-bird having been introduced, the trap may now be left to itself. If the call-bird is well trained it will not be many minutes before the birds of the neighborhood will be attracted to the spot by its cries. Ere long one less cautious than the rest will be seen to perch upon the top of the cage. He soon discovers the bait, and alighting upon the perch, throws it asunder, and in an instant the trap door closes over its captive.

The cage is sometimes constructed double, having two compartments beneath for call-birds, and two traps above, in general resembling two of the single traps placed side by side. The decoy bird is not an absolute necessity to the success of the trap. Many birds are caught simply by the bait alone. The trap cage, when constructed on a larger scale, is often successfully employed in the capture of the owl. In this case it is baited with a live mouse or bird, and set during the evening in a conspicuous place. A trap working on this principle, being especially adapted to the capture of the owl, will be noticed hereafter.

THE SPRING NET TRAP.

Although slightly complicated in construction, our next ill.u.s.tration presents one of the prettiest bird traps on record, and may be made in the following manner, and by frequently referring to the picture, our explanation will be easily understood.

The first step is to make or procure a low flat box, about fifteen inches long, by ten inches in width, with a depth of about two inches. Next fasten an interior box, of the same [Page 81]

height, leaving a s.p.a.ce of about three-quarters of an inch between them all round. A platform should now be made. Let it be of such a size that it will just fit in the interior box, with a very slight s.p.a.ce all around its edge. It should then be pivoted in the upper part of this box by two small slender pins, one being driven through into its edge, at the centre of each end. Let it be sensitively poised. The next thing to be done, is to arrange the spindle and catch. The latter should consist of a tack or small bit of wood fastened on the middle of the platform, about an inch from one end, as seen both in the main ill.u.s.tration and in the diagram at (_b_).

[Ill.u.s.tration]

The spindle should consist of a flat piece of wood, secured with a leather hinge to the edge of the outside box, directly opposite the catch. Let it be long enough to reach and barely hold itself beneath the catch. When thus in its position, two small plugs should next be driven into the edge of the inner box, one on each side of the spindle, thus holding it in place. A glance at our ill.u.s.tration makes this clear. The netting and "hoop" are next in order. The hoop should consist of an iron wire of the diameter of common telegraph wire.

For a box of the size we have given, a length of about twenty-eight inches will be found to answer. Before making the hoop, however, its hinges should be ready for it. Two screw eyes, or staples of bent wire should be driven into the bottom of the box between the two walls, one in the exact middle of each side. The iron wire should now be bent so as to fit round and settle into the s.p.a.ce between the boxes, letting each end rest [Page 82]

over the screws in the bottom. It will be found that there will be enough surplus wire on each end to form into a loop with the pincers. These loops should be pa.s.sed through the screws or rings already inserted, and then pinched together; the hinge will thus be made, and will appear as at (_c_). If properly done, they should allow the hoop to pa.s.s freely from one end of the box to the other, and settle easily between the part.i.tions. If this hinge should prove too complicated for our young readers, they may resort to another method, which, although not so durable, will answer very well. In this case the wire will only need to reach to the exact middle of the long sides. No surplus being necessary, a length of twenty-six inches will be exactly right. On each end a short loop of tough Indian twine should be tied. By now fastening these loops to the bottom of the box with tacks, in the place of screws, it will form a hinge which will answer the purpose of the more complicated one.

[Ill.u.s.tration]

The netting should consist of common mosquito gauze, or, if this cannot be had, any thin cloth may be subst.i.tuted. It should be sewed fast to the iron wire, from hinge to hinge, and then, with the hoops resting in its groove, the netting should be drawn over the platform, and tacked to the bottom of the groove, on its remaining half. It should rest loosely over the platform to allow plenty of s.p.a.ce for the bird.

But one more addition, and the trap is finished. We have mentioned the use of elastics in other varieties: they are of equal use here, and should be attached to the hoop as seen at (_a_) in the section drawing, the remaining ends being fastened to the bottom of the groove, as there indicated. These elastics should be placed on both sides, and stretched to such a tension as will draw the hoop quickly from one side to the other.

It will now be easy to set the trap. Draw the hoop back to the opposite end, tucking the netting into the groove; lower the spindle over it, resting it between the two little plugs, and securing its end beneath the catch on the platform. If the bait, [Page 83]

consisting of bread-crumbs, berries, insects, or the like, be now sprinkled on the platform, the trap is ready for its feathered victim. It will easily be seen that the slightest weight on _either_ side of this poised platform will throw the catch from the end of the spindle, and release the hoop and the platform in an instant is covered by the net, capturing whatever unlucky little bird may have chanced to jump upon it. This is a very pretty little trap, and will well repay the trouble of making it.

A SIMPLER NET TRAP.

[Ill.u.s.tration]

Much ingenuity has been displayed in the construction of bird traps of various kinds, but often the ingenuity has been misplaced, and the result has been so complicated as to mar its usefulness for practical purposes. The examples of net traps presented in this volume are so simple that the merest tyro can readily understand them. What can be more so than the present example, and yet it is as sure in its effect, and _surer_ than those other varieties of more complicated construction. One necessary element in a trap of any kind is, that the bearings are slight and that they spring easily. To obtain this requisite it is necessary to overcome friction as much as possible, using only a small number of pieces, and having as few joints and hinges only as are absolutely necessary. The present variety possesses advantages on this account. It is constructed somewhat on the principle of the ordinary steel trap, and also resembles in other respects the one we have just described, although much simpler. We give only a section drawing, as this will be sufficient. The long side of a flat board of about eight by sixteen inches is shown at (_a_); (_b_) indicates the loops of a bent wire, to which the netting is attached, as in the trap just described, [Page 84]

the loops being fastened to the board as in the other variety; (_g_) consists of a small bit of wood an inch or so in length and half an inch in width. It should be tacked on to the middle of the one end of the board and project about a half inch above the surface. To the top of this the spindle (_c_) should be attached by a leather or staple hinge. The spindle should be of light pine, five inches in length and a quarter of an inch square, bevelled; on the under side of one end (_d_) is the catch or bait piece, and should be whittled out of a shingle or pine stick of the shape shown, the width being about a half an inch or less. One side should be supplied with a slight notch for the reception of the spindle, and the other should project out two or three inches, being covered on the top with a little platform of pasteboard, tin, or thin wood either glued or tacked in place. To attach this piece to the main board, two small wire staples may be used, one being inserted into the bottom end of the piece and the other being hooked through it, and afterward tacked to the bottom of the trap, thus forming a loop hinge. Another method is to make a hole through the lower tip of the bait piece by the aid of a red-hot wire, as seen at (_d_), afterwards inserting a pin and overlapping its ends with two staples driven into the bottom board, as shown at (_e_). In our last mentioned net trap the spring power consisted of rubber elastic, and the same may be used in this case, if desired, but by way of variety we here introduce another form of spring which may be successfully employed in the construction of traps of various kinds. It is shown at (_o_) and consists merely of a piece of tempered hoop iron, so bent as to act with an upward pressure. It should be about three inches long by half an inch wide. About three-quarters of an inch should be allowed for the two screws by which it is to be attached to the board. The rest should be bent upward and thus tempered by first heating almost to redness, and then cooling in cold water.

One of these springs should be fastened to the board on each side, directly under the wire and quite near the hinge, in the position shown in the main drawing. Now draw back the net, lower the spindle and catch its extremity in the notch of the bait piece, and the trap is set as in our ill.u.s.tration. Sprinkle the bait on the platform, and lay the machine on the ground where birds are known to frequent; and it is only a matter of a few hours or perhaps minutes, before it will prove its efficacy. In order to prevent the bird from raising the wire and thereby escaping, it is well to fasten a little tin [Page 85]

catch (_f_) at the end of the board. This will spring over the wire and hold it in its place.

THE UPRIGHT NET TRAP.

The following is another novelty in the way of a bird-trap, somewhat similar to the one we have just described, in its manner of working.

Procure two pieces of board about a foot square. Nail one to the edge of the other, as represented in our engraving. A stout wire is the next requisite. It should be about thirty inches long, and bent either into a curve or into two corners, making three equal sides. Each end of the wire should then be bent into a very small loop for the hinge. On to this wire the netting should then be secured as in the two previous examples, after which the ends of the wire may be tied with string or hinged on wire staples into the angle of the two boards, as seen in our ill.u.s.tration. Allow the wire now to lie flat on the bottom board, and then proceed to tack the netting around the edges of the upright board. Two elastics should next be fastened to the wire on each side, securing their loose ends to the bottom of the trap. They should be tightly drawn so as to bring the wire down with a snap. The spindle of this trap should be about eight or nine inches long, square and slender,--the lower end being flattened, and the upper end secured to the top edge of the upright board by a hinge of leather or string.

An excellent hinge may be made with a piece of leather an inch and a half long, by half an inch in width, one half of the length being tied around the end of the spindle, and the other tacked on to the upper edge of the board.

The platform is given by itself at (_a_) in the same picture. It may be made of very thin wood--cigar box wood, for instance, or even thick pasteboard. It consists of three pieces. The piece which is hinged into the angle of the boards should be about three inches in length; the platform piece ought not to be more than four inches square, and the upright piece only long enough to reach the tip of the spindle when the platform is raised, as shown in our engraving.

The hinge piece should be cut to an edge on that end where the leather is fastened, the opposite end being bevelled off in order that the platform may rest and be tacked or glued firmly upon it.

The diagram (_a_) will make this all very clear.

When the platform is all made and fastened in its place, the [Page 86]

trap may be set. Draw the hoop back as far as possible, and lower the spindle over its edge, catching it behind the upright stick on the platform. If the trap is properly constructed, the pressure of the spindle on the platform will suffice to hold it up as seen in our ill.u.s.tration. The upright stick on the back of the platform should never be more than an inch and a half from the back of the trap. If need be, a slight notch may be made in the end of the spindle and a small tack driven into the back of the upright stick to correspond to it. By thus fitting the notch under the head of the tack, it will be sure to hold the platform in the right position.

But it should be carefully tested before setting, to see that it springs easily.

[Ill.u.s.tration]

When thus set sprinkle the bait on the platform, scattering a little also on the bottom of the trap and on the ground directly around it.

The little birds will soon spy the tempting morsels, and alighting on the trap are misled, and the slightest peck or pressure on the platform where the bait is most bounteously spread brings down the wire and net with a _snap_, and the little creature is secured without harm.

[Ill.u.s.tration: Method 2.]

Our next ill.u.s.tration shows another method of constructing the platform.

It should be about three or four inches square, [Page 87]

and on the middle of one of its edges the upright catch piece should be fastened. This piece, as will be seen in our engraving, should be cut spreading at the bottom so as to admit of being secured to the platform by two brads, the tip being cut to a point. The total length of this piece should not be over two and a half inches. When tacked in place, a third brad should be inserted between the other two and exactly in the centre of the side of the platform. This latter brad is to act as the pivot, or hinge, and should project about a quarter of an inch, as seen at (_a_). On the opposite edge of the platform another larger brad should be driven, having its end filed to a blunt point, as in (_b_). If the filing would be too tedious, a plug of hard wood of the required shape would answer every purpose. The upright props which support the platform should be cut of thin wood. Let one be an inch and a half long and half an inch wide, the other being an inch in length. Each should have one end whittled to a point, which will admit of its being inserted in a gimlet hole in the bottom of the trap. These gimlet holes should be made at least half an inch in depth. Make the first at about an inch or so from the back of the trap. Into this insert the shorter pieces, broadside front. Lay the pivot brad of the platform on the top of this piece and insert over it a small wire staple, as seen at (_a_). Elevate the platform evenly and determine the spot for the other gimlet hole, which should be directly beneath the point of the filed brad. Be sure that it is in the middle of the board, so that the platform may set squarely, and be perfectly parallel with the sides. Insert the remaining prop in its place, and the platform is complete. The overhanging spindle now requires a little attention. This should be whittled off on each side, bringing it to a point at the tip. On each side of the spindle a long plug should then be driven into the back piece, as our ill.u.s.tration shows. These should be far enough apart to allow the spindle to pa.s.s easily between them. The _setting_ of the trap is plainly shown [Page 88]

in our engraving. The spindle being lowered between the plugs is caught finely on the tip of the catch-piece. The blunt point at the opposite end of the platform should have a slight hollow made for it in the prop against which it presses. If the platform be now strewn with bait, the little machine is ready. It is certainly very simple and will be found very effective.

THE BOX OWL TRAP.

The use of a box trap for the capture of an owl is certainly an odd idea, but we nevertheless ill.u.s.trate a contrivance which has been successfully used for that purpose.

© 2024 www.topnovel.cc