8 ft. flooring for bottom.
2 cleats, 7/8 by 1-1/2 by 57 in., S-4-S.
Plane and square the ends of all the rails and posts. Lay out the lap joints for the back rails and posts. Use a knife line for this and saw exactly to the line to avoid tr.i.m.m.i.n.g with the chisel. When sawing be careful to cut exactly halfway through the thickness of each piece. In the same way make the lap joints between the front rail and posts. Have the two end rails exactly the same length and proceed to fasten the front and back posts to them, using 4-in. lag screws and washers. Bore through the posts and part way into the ends of the end rails for the lag screws.
[Ill.u.s.tration: Detail of the Porch Swing]
The slats are mortised 1/2 in. into the back rails, or a 3/8-in. groove may be planed in these rails, the entire distance between joints, to receive the slats. A rabbeting plane will be needed for this. The arm rests lap over the back posts and are held to them with 2-in.
round-head screws. They may be fastened to the top of the front posts with round-head screws or dowel pins.
Ordinary pine flooring makes a good, tight seat, or 7/8-in. board may be used if desired. Fasten the cleats, which support the seat, to the front and back lower rails with 1-1/2-in. screws.
To bring out the beautiful grain of southern pine, stain it brown or black and finish with two coats of waterproof varnish.
A FOOT WARMER
This foot warmer is so constructed that two bricks may be heated and placed inside of the stool.
Oak is the most suitable wood to use, and the following pieces will be needed:
4 legs, 1-1/4 by 1-1/4 by 8 in., S-4-S.
4 side rails, 7/8 by 3 by 8-1/2 in., S-2-S.
4 top pieces, 7/8 by 1-1/2 by 12 in., S-2-S.
1 bottom piece, 7/8 by 8-1/2 by 8-1/2 in., S-2-S.
1 piece asbestos, 8-1/2 by 8-1/2 in.
4 pieces asbestos, 2 by 8-1/2 in.
1 sheet of bra.s.s, 13 by 13 in., 17 gauge.
2 hinges, 1 elbow catch, 3 doz. ornamental tacks.
The work may be started by shaping the four legs and cutting the mortises for the rails. Tenons are cut on the ends of the rails to fit in the mortises made in the posts. They are then glued together, care being taken to get the stool perfectly square.
The top frame can now be made and covered with the sheet of bra.s.s. The frame has mitered corners and the inside of the frame must be even with the inside of the rails. This in turn is fastened to the stool with the two hinges on the back and the elbow catch on the front side to keep it closed.
[Ill.u.s.tration: Detail of the Foot Warmer]
The design on the bra.s.s can be made by tacking it on a board, laying out the design and piercing the background with some sharp-pointed tool.
This leaves the design raised with a smooth surface.
The bra.s.s can now be removed from the board, placed on the frame and fastened with the ornamental tacks.
Turn the stool bottom side up and line the inside of the rails with asbestos; then place the bricks on the inside of the stool. Both should fit up tight to the bra.s.s when the bottom is in place.
[Ill.u.s.tration: Oak Stool with Bra.s.s Cover]
The stool is now ready for the finish, which can be of some stain to match the other furniture in the room where it is to be used.
A PLATE RACK FOR THE DINING ROOM
This plate rack can be made of any kind of wood and finished to match other pieces of furniture in the room, but as it is of mission design, oak is the most suitable lumber, as it takes the mission stain so nicely.
The material required is as follows:
4 posts, 1-1/2 by 1-1/2 by 28 in., S-4-S.
1 top, 7/8 by 7-1/4 by 48 in., S-2-S.
2 plate rails, 7/8 by 6-1/4 by 32 in., S-2-S.
2 back boards, 7/8 by 7-1/4 by 25 in., S-2-S.
2 side boards, 7/8 by 5-1/4 by 25 in., S-2-S.
4 shelves, 7/8 by 6-1/2 by 8-1/4 in., S-2-S.
2 plate rests, 7/8 by 7/8 by 32 in., S-4-S.
[Ill.u.s.tration: Detail of Plate Rack]
This stock is specified to exact thickness, but some allowance is made for tr.i.m.m.i.n.g on the edges and ends.
Begin work by squaring up the posts to length and beveling the top ends, then trim the back and side boards. These are nailed together, lapping the back board over the side board. The posts are fastened with dowels placed at equal distances apart. Hot glue is used in the joints.
[Ill.u.s.tration: Dining-Room Plate Rack]
The four shelves are now put in place. These are notched out to fit around the posts and are nailed and glued.
While the glue is hardening on these, the plate rails can be cut. These have 7/8-in grooves near the front edge to receive the lower edge of the plates when resting against the two strips placed 5 in. above the plate rails and far enough back to prevent the plates from falling forward.
The rails are fastened to the two sides with dowels, three at each end being sufficient. The two strips fit in mortises cut in the side pieces.
The top is then put on. This fits around the posts and rests on the sides. Hooks on which to hang cups are placed under the rails. All parts are thoroughly sandpapered before the stain is applied.
A MISSION SIDEBOARD
[Ill.u.s.tration: Sideboard for the Dining-Room Set]
The sideboard is a piece designed to go with the armchair and side chair with similar paneling design. Like these chairs the sideboard should be made of hard wood and should be similarly finished. The drawer pulls, if not made of wood, should be of such metal and design as to harmonize with the mission style. Wrought-iron effects in plain outlines are appropriate.
Drawer sides, bottoms and backs may be made of some soft wood, such as yellow poplar. The small top drawer may be lined with ooze leather for holding silverware.
Obtain the following stock:
2 posts, 2 by 2 by 50 in., S-4-S.
2 posts, 2 by 2 by 39 in., S-4-S.
1 top, 1 by 23 by 58 in., S-2-S.