** A Handy Calendar [196]
[Ill.u.s.tration: The Knuckles Designate the 31 Day Months]
"Thirty days hath September, April, June and November," etc., and many other rhymes and devices are used to aid the memory to decide how many days are in each month of the year. Herewith is ill.u.s.trated a very simple method to determine the number of days in any month. Place the first finger of your right hand on the first knuckle of your left hand, calling that knuckle January; then drop your finger into the depression between the first and second knuckles, calling this February; then the second knuckle will be March, and so on, until you reach July on the knuckle of the little finger, then begin over again with August on the first knuckle and continue until December is reached. Each month as it falls upon a knuckle will have 31 days and those down between the knuckles 30 days with the exception of February which has only 28 days.
--Contributed by Chas. C. Bradley, West Toledo, Ohio.
** The Fuming of Oak [196]
Darkened oak always has a better appearance when fumed with ammonia. This process is rather a difficult one, as it requires an airtight case, but the description herewith given may be entered into with as large a case as the builder cares to construct.
Oak articles can be treated in a case made from a tin biscuit box, or any other metal receptacle of good proportions, provided it is airtight. The oak to be fumed is arranged in the box so the fumes will entirely surround the piece; the article may be propped up with small sticks, or suspended by a string. The chief point is to see that no part of the wood is covered up and that all surfaces are exposed to the fumes. A saucer of ammonia is placed in the bottom of the box, the lid or cover closed, and all joints sealed up by pasting heavy brown paper over them. Any leakage will be detected if the nose is placed near the tin and farther application of the paper will stop the holes. A hole may be cut in the cover and a piece of gla.s.s fitted in, taking care to have all the edges closed. The process may be watched through the gla.s.s and the article removed when the oak is fumed to the desired shade.
Wood stained in this manner should not be French polished or varnished, but waxed.
The process of waxing is simple: Cut some beeswax into fine shreds and place them in a small pot or jar. Pour in a little turpentine, and set aside for half a day, giving it an occasional stir. The wax must be thoroughly dissolved and then more turpentine added until the preparation has the consistency of a thick cream. This can be applied to the wood with a rag and afterward brushed up with a stiff brush.
** How to Make an Electrolytic Rectifier [197]
[Ill.u.s.tration: Electrolytic Rectifier and Connections]
Many devices which will change alternating current to a direct current have been put on the market, but probably there is not one of them which suits the amateur"s needs and pocketbook better than the electrolytic rectifier.
For the construction of such a rectifier four 2-qt. fruit jars are required. In each place two electrodes, one of lead and one of aluminum. The immersed surface of the aluminum should be about 15 sq. in. and the lead 24 sq. in. The immersed surface of the lead being greater than that of the aluminum, the lead will have to be crimped as shown in Fig, 1. In both Fig. 1 and 2, the lead is indicated by L and the aluminum by A.
The solution with which each jar is to be filled consists of the following:
Water 2 qt.
Sodium Carbonate 2 tablespoonfuls Alum 3 tablespoonfuls
Care should be taken to leave the connections made as shown in Fig. 2. The alternating current comes in on the wires as shown, and the direct current is taken from the point indicated.
The capacity of this rectifier is from 3 to 5 amperes, which is sufficient for charging small storage batteries, running small motors and lighting small lamps.
--Contributed by J. H. Crawford, Schenectady, N. Y.
** The Rolling Marble [197]
Take a marble and place it on a smooth surface, The top of a table will do. Ask someone to cross their first and second fingers and place them on the marble as shown in the ill.u.s.tration. Then have the person roll the marble about and at the same time close the eyes or look in another direction. The person will imagine that there are two marbles instead of one.
[Ill.u.s.tration: Rooling Marble]
** A Gas Cannon [197]
If you have a small cannon with a bore of 1 or 1-1/2 in., bore out the fuse hole large enough to tap and fit in a small sized spark plug such as used on a gasoline engine. Fill the cannon with gas from a gas jet and then push a
[Ill.u.s.tration: Gas Cannon Loaded]
cork in the bore close up to the spark plug. Connect one of the wires from a battery to a spark coil and then to the spark plug.
Attach the other wire to the cannon near the spark plug. Turn the switch to make a spark and a loud report will follow.
--Contributed by Cyril Tegner, Cleveland, O.
** Old-Time Magic-Part VI [198]
** A Handkerchief Mended after Being Cut and Torn
Two persons are requested to come forward from the audience to hold the four corners of a handkerchief. Then beg several other handkerchiefs from the audience and place them on the one held by the two persons. When several handkerchiefs have been acc.u.mulated, have some one person draw out one from the bunch and examine for any marks that will determine that this handkerchief is the one to be mended after being mutilated. He, as well as others, are to cut off pieces from this handkerchief and to finally tear it to pieces.
The pieces are then all collected and some magic spirits thrown over the torn and cut parts; tie them in a small package with a ribbon and put them under a gla.s.s, which you warm with your hands.
After a few seconds" time, you remove the gla.s.s, as you have held it all the time, and take the handkerchief and unfold it; everyone will recognize the mark and be amazed not to find a cut or tear in the texture.
This trick is very simple. You have an understanding with some one in the company, who has two handkerchiefs exactly alike and has given one of them to a person behind the curtain; he throws the other, at the time of request for handkerchiefs, on the handkerchiefs held for use in the performance of the trick. You manage to keep this handkerchief where it will be picked out in preference to the others, although pretending to thoroughly mix them up. The person selected to pick out a handkerchief naturally will take the handiest one. Be sure that this is the right one.
When the handkerchief has been torn and folded, put it under the gla.s.s, on a table, near a part.i.tion or curtain. The table should be made with a hole cut through the top and a small trap door fitted snugly in the hole, so it will appear to be a part of the table top. This trap door is hinged on the under side and opens into the drawer of the table and can be operated by the person behind the curtain who will remove the torn handkerchief and replace it with the good one and then close the trap door by reaching through the drawer of the table.
** The Magic Knot [198]
This is a very amusing trick which consists of tying one knot with two ends of a handkerchief, and pulling the
[Ill.u.s.tration: Tying and Untying a Knot]
ends only to untie them again. Take the two diagonal corners of a handkerchief, one in each hand and throw the main part of the handkerchief over the wrist of the left hand and tie the knot as shown in the ill.u.s.tration. Pull the ends quickly, allowing the loop over the left hand to slip freely, and you will have the handkerchief without any knot.
** A Good Mouse Trap [198]
When opening a tomato or other small can, cut the cover crossways from side to side making four triangular pieces in the top. Bend the four ends outward and remove the contents, wash clean and dry and then bend the four ends inward, leaving a hole about 3/4 in.
in diameter in the center. Drop in a piece of bread and lay the can down upon its side and the trap is ready for use. The mouse can get in but he cannot get out.
--Contributed by E. J. Crocker, Victor, Colo.
** Finishing Aluminum [198]
Rubbing the surface of an aluminum plate with a steel brush will produce a satin finish.