In its unsized state the paper is too absorbent for use, and it should be sized freshly as needed for work. This is done by brushing a thin solution of gelatine over the smooth surface of the sheets of paper.
A drawing-board rather larger than the sheets of paper, placed as shown in fig. 17, with its lower edge resting on a basin of warm size, will be found a convenient arrangement.
[Ill.u.s.tration: Plate VII. Impression of a portion of detail from a j.a.panese woodblock (very nearly actual size).
(_To face page 48._)]
The sheet gelatine sold by grocers for cooking makes an excellent size.
Six of the thin sheets to a pint of water is a good strength.[3] The gelatine is dissolved in hot water, but should not be boiled, as that partially destroys the size. When dissolved, a little powdered alum is also stirred in, about as much as will lie on a shilling to a pint of water. The addition of the alum is important, as it acts as a mordant and helps to make a better colour impression.
[3] See also p. 75.
[Ill.u.s.tration: FIG. 17.--Drawing of sizing of paper.]
In applying the size to the paper a four-inch broad flat paste brush is used. The paper is laid on the slanting board and the size brushed backward and forward across the paper from the upper end downward. Care must be taken not to make creases in the paper, as these become permanent. To avoid this the lower end of the sheet may be held with the left hand and raised when necessary as the brush pa.s.ses downwards. The waste size will run down to the basin, but the paper need not be flooded, nor should its surface be brushed unnecessarily, but it must be fully and evenly charged with size. The sheet is then picked up by the two upper corners (which may conveniently be kept unsized) and pinned at each corner over a cord stretched across the workroom. The sheets are left hanging until they are dry. The j.a.panese lay the paper on the cord, letting the two halves of the sheet hang down equally on either side.
The process of sizing and drying the sheets of paper is ill.u.s.trated in a print shown in the collection at the South Kensington Museum.
When the paper is quite dry it is taken down, and if required at once for printing should be cut up into sheets of the size required, with sufficient margin allowed to reach the register marks. It is best to cut a gauge or pattern in cardboard for use in cutting the sheets to a uniform size.
A few sheets of unsized paper are needed as damping sheets, one being used to every three printing sheets. The damping sheets should be cut at least an inch wider and longer than the printing sheets. Two wooden boards are also required. The sheets of printing paper are kept between these while damping before work.
To prepare for work, a damping sheet is taken and brushed over evenly with water with a broad brush (like that used for sizing). The sheet must not be soaked, but made thoroughly moist, evenly all over. It is then laid on one of the two boards, and on it, with the printing side (the smoother side) downward, are laid three of the sized sheets of printing paper. On these another moist damping sheet is laid, and again three dry sheets of printing paper, face downwards, and so on alternately to the number of sheets of the batch to be printed. A board is placed on the top of the pile.
The number of prints to be attempted at one printing will vary with the kind of work and with the printer"s experience. The printing may be continued during three days, but if the paper is kept damp longer, there is danger of mould and spotting. With work requiring delicate gradation of colour and many separate block impressions twenty or thirty sheets will be found sufficient for three days" hard work. The professional printers of j.a.pan, however, print batches of two hundred and three hundred prints at a time, but in that case the work must become largely mechanical.[4]
[4] See Chapter XIII for further experience on this point.
The batch of paper and damping sheets should remain between the boards for at least half an hour when new sheets are being damped for the first time. The damping sheets, all but the top and bottom ones, should then be removed and the printing sheets left together between the boards for some time before printing. An hour improves their condition very much, the moisture spreading equally throughout the batch of sheets. Before printing they should be quite flat and soft, but scarcely moist to the touch. If the sheets are new, they may even be left standing all night after the first damping, and will be in perfect condition for printing in the morning without further damping. No weight should be placed on the boards.
Although no paper has. .h.i.therto been found that will take so perfect an impression from colour-blocks as the long-fibred j.a.panese paper, yet it should be the aim of all craftsmen to become independent of foreign materials as far as possible. There is no doubt that our paper-makers should be able to produce a paper of good quality sufficiently absorbent to take colour from the wet block and yet tough enough to bear handling when slightly damp.
If a short-fibred paper is made without size, it comes to pieces when it is damped for printing. But the amount of absorbency required is not so great as to preclude the use of size altogether. It is a problem which our paper-makers could surely solve. A soft, slightly absorbent, white paper is required. At present nothing has been produced to take the place of the long mulberry fibre of the j.a.panese, which prints perfectly, but it is far from being pure white in colour. A white paper would have a great advantage in printing high and delicate colour schemes.
INK
Next in importance is the preparation of the ink for printing the key-block or any black or grey parts of a design. As a rule the key-block is printed black, more or less diluted with paste; indeed the key-block is often printed very faintly by means of paste only just tinged with a trace of black.
The use of colour for the key-block is treated in Chapter VII. The ink is prepared as follows. Take a stick of solid Chinese ink of good quality, and break it with a hammer into fragments; put these to soak in a pot with water for three or four days. (The quality of the sticks of Chinese ink varies greatly. The cheap sticks make a coa.r.s.e and gritty ink which does not print well.) Day by day pour off the water, adding fresh, so that the glue that soaks out of the softened black fragments is removed. Three days is usually long enough for this. If left too long the whole ma.s.s goes bad and is spoiled. When the black ma.s.s is soft and clean drain off the water and rub the ink smooth in a dish with a bone palette knife. It is then ready for use, but would rapidly go bad if not used up at once, so that a preservative is necessary to keep a stock of ink in good condition. An effective method is to put the ink at once into a well-corked, wide-mouthed bottle. To the under side of the cork is nailed a little wad of unsized paper soaked with creosote. By this means ink can be kept in perfect condition for weeks or months. A drop of fresh creosote should occasionally be put on the wad fixed to the cork.
[Ill.u.s.tration: FIG. 18.--Cork of ink-bottle with wad for preservative.]
Fresh ink may at any time be obtained rapidly in small quant.i.ties by rubbing down a stick of Chinese ink on a slab in the ordinary way, but this is very laborious, and is only worth while if one needs a small quant.i.ty of a glossy black, for which the rubbed-down ink containing all its glue is the best.
COLOUR
Any colour that can be obtained in a fine dry powder may be used in wood-block printing. Some artists have succeeded in using ordinary water colours sold in tubes, by mixing the colour with the rice paste before printing; but the best results are obtained by the use of pure, finely ground dry colour mixed only with water, the rice paste being added actually on the block.
Most of the artists" colour merchants supply colour by weight in the form of dry powder: any colour that is commonly used in oil or water-colour painting may be obtained in this state. A stock of useful colours should be kept in wide-necked bottles.
A few shallow plates or small dishes are needed to hold colour and a bone or horn palette knife for mixing and rubbing the colour into a smooth paste in the dishes. Small bone paper knives are useful for taking colour from the bottles.
When the colour scheme of a print is made certain--and this is best done by printing small experimental batches--it is a good plan to have a number of covered pots equal to the number of the different colour impressions, and to fill these with a quant.i.ty of each tint, the colour or colours being mixed smoothly with water to the consistency of stiff cream.
Some colours will be found to print more smoothly and easily than others. Yellow ochre, for instance, prints with perfect smoothness and ease, while heavier or more gritty colours tend to separate and are more difficult. In the case of a very heavy colour such as vermilion, a drop of glue solution will keep the colour smooth for printing, and less paste is necessary. But most colours will give good impressions by means of rice paste alone. It is essential, however, that only very finely ground colours of good quality should be used.
PASTE
A paste must be used with the colour in order to hold it on to the surface of the paper and to give brilliancy. The colour, if printed without paste, would dry to powder again. The paste also preserves the matt quality which is characteristic of the j.a.panese prints.
Finely ground rice flour may be obtained from grocery dealers. An excellent French preparation of rice sold in packets as _Creme de Riz_ is perfect for the purpose of making paste for printing. It should be carefully made as follows: While half a pint of water is put to boil in a saucepan over a small spirit lamp or gas burner, mix in a cup about two teaspoonfuls of rice flour with water, added little by little until a smooth cream is made with no lumps in it. A bone spoon is good for this purpose. Pour this mixture into the boiling water in the saucepan all at once, and stir well till it boils again, after which it should be left simmering over a small flame for five minutes.
When the paste has cooled it should be smooth and almost fluid enough to pour: not stiff like a pudding.
While printing, a little paste is put out in a saucer and replenished from time to time.
Fresh paste should be made every day.
CHAPTER VI
Detailed Method of Printing
Success in printing depends very much on care and orderliness. It is necessary to keep to a fixed arrangement of the position of everything on the work-table and to have all kept as clean as possible. To see the deft and unhurried work of a j.a.panese craftsman at printing is a great lesson, and a reproach to Western clumsiness.
The positions indicated by the diagram on page 11 will be found to be practical and convenient.
The special tools used in printing are the "baren" or printing pad, which is the only instrument of pressure used, and the printing brushes.
THE BAREN OR PRINTING PAD
As made by the j.a.panese, the baren is about five inches in diameter, and consists of a circular board upon which a flat coil of cord or twisted fibre is laid. This is held in place by a covering made of a strip of bamboo-sheath, the two ends of which are twisted and brought together at the back of the board so as to form a handle. The flat surface of the bamboo-sheath is on the under side of the pad when the handle is uppermost. The ribbed bamboo-sheath is impervious to the dampness of the paper in printing, and the pad may be used to rub and press directly on the back of the damp paper as it lies on the block without any protective backing sheet. The collotype reproduction facing page 12 shows the shape and character of the baren.
j.a.panese printing pads may be obtained from some of the artists"
colour-men, or from j.a.pan through various agencies. They are by far the best instrument for the purpose. A pad lasts a considerable time, and when the bamboo sheath wears through may be re-covered as described below. If the new bamboo sheath is un.o.btainable, the baren may be re-covered by a sheet of vegetable parchment (of the kind used for covering pots of jam), laid on when wet, and twisted and bound at the end like the original bamboo covering. A baren used and re-covered when worn will last for an indefinite time in this way.
TO RE-COVER A WORN BAREN WITH BAMBOO SHEATH
Damp the new leaf in water with a brush on both sides thoroughly.