When putting the frame together, glue should be used on the joints, as it makes them much stiffer. Be careful to get the frame together perfectly square, or it will be hard to fit the doors and the gla.s.s.
When it is complete, go over the whole carefully with fine sandpaper and remove all rough spots. Sc.r.a.pe all the surplus glue from about the joints, as stain will not take when there is any glue. The closet can be finished in any one of the many mission stains supplied by the trade for this purpose.
[Ill.u.s.tration: Oak Bedstead Complete]
AN OAK BEDSTEAD
The accompanying sketches show an artistic design for a mission bed, so simple in construction and design that most any one that has a few tools and a knowledge of their use can make it. It is best made of quarter-sawed oak, as this wood is the easiest to procure and work up and looks well with any finish. If the stock is ordered from the mill ready cut to length, squared and sanded, much of the hard labor will be saved.
The following is a list of the material needed:
2 posts, 2-1/2 by 2-1/2 by 50 in.
2 posts, 2-1/2 by 2-1/2 by 44 in.
2 end rails, 1 by 6 by 56 in.
2 side rails, 1 by 6 by 78 in.
5 end rails, 1 by 4 by 56 in.
3 end rails, 1 by 2 by 56 in.
8 vertical slats, 3/8 by 6 by 11-1/2 in.
10 vertical slats, 3/8 by 2 by 11-1/2 in.
2 cleats, 1 by 1 by 78 in.
5 slats, 3/4 by 3 by 55-1/2 in.
20 blocks, 1 by 1 by 3 in.
Square up the four posts in pairs and lay out the mortises as per drawing. To do this, lay them side by side on a flat surface with the ends square and mark them with a try-square. The tenons on the end rails are laid out in the same manner as the posts. Four of the end rails should be marked and mortises cut for the upright slats as shown in the detail drawing. The tenons on the end rails are about 1 in. long, while those on the slats can be 3/4 in. long. Fit all the parts together before gluing to see that they fit square and tight. After the glue has been applied clamp them together perfectly square and set them away to dry. They should dry at least twenty-four hours before the clamps are removed.
[Ill.u.s.tration: Details of Oak Bedstead]
While the ends are drying, the side rails can be made. These have a 1-in. square cleat screwed to the inner side for the slats to rest upon.
If springs are used, five slats will be sufficient. They can be placed where the springs will rest upon them. After the position of the slats has been located, nail small blocks at their sides to hold them in place. For fastening the side rails to the posts, patent devices can be purchased at a local hardware store. The posts will have to be mortised to receive these, and care should be exercised to get them in the right place.
When the bed is complete go over it carefully and sc.r.a.pe all the surplus glue from about the joints, as the finish will not take where there is any glue. Remove all rough spots with fine sandpaper; then apply the stain you like best, which may be any of the many mission stains supplied by the trade for this purpose. If this bed is well made and finished, it will be an ornament to any home.
AN OAK FOOTSTOOL
The footstool shown in the ill.u.s.tration can be made from any kind of wood, but when it is intended to be finished in mission style, quarter-sawed oak will produce the best effect. The material needed will be as follows:
1 top, 1 by 9-1/2 by 12 in., S-1-S.
2 legs, 3/4 by 8 by 12 in., S-2-S.
1 brace, 3/4 by 7 by 9 in., S-1-S.
Order these pieces cut to length, squared and sanded. A full-sized layout of the front view should be made to get the correct bevels for the legs and brace. The design of the legs can be varied to suit the fancy of the maker. For such a design as shown draw one-half of it on paper; fold on the center line and with scissors cut both sides of the outline by following the lines drawn. Trace around this pattern on the wood, and saw out with a compa.s.s or keyhole saw. The sawed edges should be smoothed and sandpapered.
[Ill.u.s.tration: Details of Footstool]
The perforation in the top board is made by first boring holes, then tr.i.m.m.i.n.g out the edges with a sharp chisel. Be sure to get the best side of the board up.
[Ill.u.s.tration: Footstool Complete]
The legs are fastened to the top and to the braces with 1-3/4-in. wood screws as shown in the detail drawing. After the stool is a.s.sembled, go over it carefully with fine sandpaper and remove all rough spots before applying the finish. This finish can be any one of the many different kinds supplied by the trade for this purpose. If this stool is well made and finished, it will be a useful and attractive article.
[Ill.u.s.tration: Table and Seat Decorated in Pyro-Carving]
A LIBRARY SET IN PYRO-CARVING
The mult.i.tude of indifferently executed small articles which followed the introduction of pyrography is beginning to disappear, people are considering the art more seriously and applying it to more dignified uses. Pyro-carving is one of the new methods of decorating furniture which is both beautiful and practical, two qualities which do not always go together.
The library set ill.u.s.trated consists of a table, 30 by 50 in., with two benches, 14 in. wide of the same length. The supports are made of selected white pine, which must be absolutely free from pitch. The pine is soft enough to work easily with the point and stands wear much better than ba.s.swood. The tops and braces are made of curly fir, all of the material must be 2-in. lumber, which dresses to about an inch and a half. All surfaces, except the faces of the supports, are given a well-rubbed coat of oil with a little burnt umber, the stain to be applied directly to the wood without a filler.
On the outside of the supports the design is drawn in with pencil, the background is then cut out smoothly with a chisel to the depth of an eighth of an inch, leaving the decoration in relief. It is then burned deeply, the background in straight flat strokes, the outlines having the effect of a sloping, dark edge. The shadows are burned in as deeply as possible and the shading is put in with the flat of the point.
A wax or egg-sh.e.l.l oil varnish finish is most suitable for this set.
[Ill.u.s.tration: Grille for an Arch]
A GRILLE WITH PEDESTALS TO MATCH
The accompanying sketch shows something unique in a grille that adds to the appearance of a home furnished in mission style. When it is stained and finished to match the furniture, it gives a consummate tone that would be difficult to obtain by any other means.
To get the best results it should be made to blend with the furniture and the arch in which it is to fit, in both weight and style. This will depend very much upon one"s preference, and for this reason full dimensions are not given. No difficulty will be experienced, however, by anyone handy with tools, in making it.
The material should be quarter-sawed oak, which can be secured planed and sanded at the mill. For the grille order 1 by 1-1/2-in. and 1/2 by 1-1/2-in. stock. The method of making the bars is shown in the detailed sketch. The two end bars should be made of solid pieces, 3/4 by 1-1/2 in., with two rectangular slots mortised in each to receive the supports. The supports should be just the right length to go in the arch. To erect, slip the end bars on the supports, hold the grille in place and fasten the bars to the sides of the arch with screws.
The size of the pedestals and the connecting pieces will depend upon the size of the arch. These connecting pieces should be well mortised into the post, and if you own your own home and intend the pedestals to become a fixture, they should also be mortised into the sides of the arch. If not, they may be fastened to the arch with blind screws. The amount of material required will depend upon the size of the arch.
A LADY"S WRITING DESK
This desk of mission style is a little more complicated than some of the other pieces of mission furniture that have been described, but anyone who has a fair knowledge of tools will not have much trouble in constructing it in the home workshop if the plans are carefully followed. Quarter-sawed oak is the best wood to use, as it is easy to work and looks best when finished. Order the stock from the mill ready cut to length, squared and sanded. Following is a list of the stock needed:
2 front posts, 2 by 2 by 30 in.